View the Status with Satellite Imagery

See what you can’t see from the ground. The status of your crop from the satellite.

Request advice today.

A satellite can see your entire farm in seconds and detect differences in vigor or water status between areas that would go unnoticed for weeks when walking the field. With Plantae satellite imagery, that information arrives analyzed and ready to act on.

The real problem

A large farm is hard to fully monitor. The satellite doesn’t get tired.

Covering a farm of tens or hundreds of hectares to check the status of the crop at every point takes time, and things can happen between visits. Water stress starting in a specific area, a zone with poorer development due to soil differences, a problem that progresses before it is visible to the naked eye.

Satellite imagery analyzes the reflectance of the vegetation to detect these differences before they become evident in the field. It does not replace the visit, but it does make it more efficient: instead of walking the entire farm, you know where to look.

What information satellite imagery provides

Two indices that show the real status of your crop.

NDVI — Vegetation index

NDVI measures vegetation vigor based on the difference between red and infrared light reflected by plants. A high value indicates healthy, active vegetation. A low value may indicate stress, lack of water, phytosanitary problems, or areas with poorer development. It allows you to compare the status of different plots or areas within the same farm.

NDWI — Water index

NDWI measures the water content in vegetation. It is especially useful for detecting areas with water stress before symptoms are visible. Combined with soil moisture data, it helps you understand whether a water problem comes from the soil or from the plant’s own condition.

What it’s used for in practice

At Plantae, satellite imagery is mainly used for two things: optimizing sensor installation by identifying the most representative areas of the farm, and monitoring the general status of the crop throughout the season to detect variations that deserve attention.

What you can do with that information

From the image to the action map.

Detect areas with problems before you see them in the field

A drop in the NDVI index in a specific area may indicate water stress, nutrient deficiency, pest damage, or any other issue affecting plant vigor. Knowing this before the visit lets you go directly to that area with a more focused diagnosis.

Optimize where to place the sensors

Before installing sensors in the field, satellite image analysis makes it possible to identify the most representative areas of the farm: the most variable ones, those that best reflect the general behavior of the crop. This improves data quality and the effectiveness of the entire installation.

Compare crop status between seasons

The historical record of satellite images allows you to compare crop vigor on the same dates in different years, identify whether certain areas systematically perform worse, and assess whether management changes are having an effect.

How we do it with Plantae

The products that make this solution possible.
This solution is implemented with Plantae’s Satellite Imagery service, which includes processing of the NDVI and NDWI indices and their visualization in Plantae Manager. It is complemented by soil sensors to close the loop between the aerial view and on-plant data.

Satellite Imagery

NDVI and NDWI indices. Crop status map for the entire farm.

Humidity Sensor

Soil water status at the key points identified by the imagery.

Air RH and Temperature Sensor

Climate data to complement crop monitoring.

Particle Sensor

Conductivity of the soil solution in areas with detected anomalies.

Who this solution is for

For farms where size or complexity makes full supervision difficult.

Large fruit, olive, or vineyard farms
On farms of more than 20–30 hectares, satellite imagery is the most efficient way to have a complete view of crop status without having to walk the entire area. It lets you prioritize the areas that require attention.
Farms with heterogeneous soils
On plots where the soil varies significantly from one area to another, satellite imagery clearly shows how those differences translate into different crop behavior, and guides sensor installation and differentiated management by zone.
Technicians who advise large farms or multiple holdings
Satellite imagery allows the technician to visually monitor the general status of several farms without traveling, detect anomalies that require a visit, and present the farmer with a clear view of the status of their crop.

FAQs

What we’re usually asked.

The frequency depends on satellite availability and weather conditions, since cloud cover prevents capture. Under normal conditions, it is possible to obtain images every few days. The Plantae team will tell you the cadence available for your area.
It is an index that measures vegetation vigor based on how plants reflect light. High values indicate healthy, active vegetation. Low values may indicate stress, phytosanitary problems, or areas with poorer development. It does not require any special technical knowledge to interpret: it is presented as a color map over your plot.
No, it complements them. Imagery provides a view of vegetation status from the air. In-field sensors provide real-time soil data. Combined, they offer a much more complete picture of what is happening on the farm.
Yes, although it is especially useful in crops with continuous plant cover: olive groves, vineyards, orchards, horticultural crops. In very low-growing crops or early development stages, the signal can be harder to interpret.
The satellite imagery service is part of Plantae’s offering. Contact the team to learn about the available options and the price for your specific case.

Know the status of your entire farm without leaving home.

Tell us the size and crop type of your farm. We’ll show you how satellite imagery can help you manage it better.